While manufacturing short stroke kits is a large part of what we do, we also do action jobs on many kinds of cowboy guns. Below you will find the services we offer. If you do not see a service you are looking for, send us an email or call and ask about it. You can find our contact information on the "Contact Us" page.

*Note: We do NOT perform work on the “winchester miroku” rifles anymore, nore do we offer new parts for those rifles!

We do however, have a VERY limited quantity of the firing pin extensions left for those rifles. They are made to the last specs from our personal machinist, and there is NO guarantee that these will perform with the newer model Miroku rifles! They are $42 each, new condition and sold as-is. There will be NO returns on these once they have sold!

 All prices below are based on the customer sending their rifle in for work!

*General labor cost: $75/hour

RIFLES

Model 66 & 73 rifles

Custom, performance action job: $350

*NOTE: If you are sending in a rifle for action work of any kind and your gun is dirty, you will be charged a $75 fee for the rifle to be professionally cleaned. Action work is a precise operation and MUST be performed with a clean rifle which includes all parts, internal frame and barrel.

This is a service that we provide before the action job and ONLY in the event that your rifle is too dirty to be worked on. Charge for this is up to the gunsmith’s discretion so please check and make sure your rifle is clean before sending it unless you simply wish to have it cleaned on-top of the action work!

* Action job includes properly fitting all internal parts, polishing critical surfaces of mating parts, tuning of all stock spring including lifter/lever springs, mainspring and extractor springs, adjusting timing if necessary, assuring that firing pin protrudes the correct amount from the bolt face, de-burring all parts and inside of receiver as needed, installing a new lever safety spring (model 73), setting the trigger pull to a crisp 2 pounds, checking action for smoothness and reliability and finally testing the feeding, extraction and firing.

  We can install more parts if you are interested. Please give us a call for options and prices!

Want more than an action job and a few parts? Check out our build options!!

Stage 1: Action job, Lever safety spring, Short stroke kit, Speed sight, Quick Cap

Stage 2: Action job, Lever safety spring, Short stroke kit, Speed sight, Stainless steel magazine spring, Stainless steel follower, Hardened extended firing pin with spring, Action springs, Aluminum carrier, Leather leather wrap, Quick cap

Stage 3: Action job, Lever safety spring, Short stroke kit, Speed sight, Stainless steel magazine spring, Stainless steel follower, Hardened extended firing pin with spring, Action springs, Aluminum carrier, Leather leather wrap, Coil mainspring kit, Leather butt stock cover, Light weight firing pin extension, Quick cap

We can always add or remove items from a stage package! Let us know when you call!

Stages of 1866/1873 Uberti Action Work:

Stage 1 - Standard Sight ($644), Tall Sight ($650), Carbine Sight ($699)
Stage 2 - Standard Sight ($879), Tall Sight, ($885), Carbine Sight ($934)
Stage 3 - Standard Sight ($1,199), Tall Sight ($1,205), Carbine Sight ($1,254)

Marlin “Performance” Competition Job.

1894/.357-45LC:

With Standard speed sight: $541

With Tall speed sight: $5547

1895/336

With Standard speed sight: $546

With Tall speed sight: $552

*NOTE: If you are sending in a rifle for action work of any kind and your gun is dirty, you will be charged a $75 fee for the rifle to be professionally cleaned. Action work is a precise operation and MUST be performed with a clean rifle which includes all parts, internal frame and barrel.

This is a service that we perform before the action job and ONLY in the event that your rifle is too dirty to be worked on. Charge for this is up to the gunsmith’s discretion so please check and make sure your rifle is clean before sending it unless you simply wish to have it cleaned on-top of the action work!

*Our Marlin competition action job Includes refitting all internal parts, polishing critical mating surfaces, replacing hammer spring for tuned coil spring, replacing lever-plunger spring with lighter coil spring, installation of “Long-hunter” one piece firing pin and spring kit, polishing and cleaning of bolt for freedom of movement, installation of a “Happy Trigger” which eliminates the “Marlin trigger flop” & sets a 3# trigger pull, a leather lever wrap, stainless steel magazine tube spring and follower, standard height or tall speed sight, feeding gets checked, firing gets checked.

SHOTGUNS

Custom professional action job:

$360

We work on the following listed shotguns:

Huglu, Baikal, Stoeger, Browning, Charles Daly, CZ hammerless, TTN, CZ exposed hammer

Includes honing the chambers, radius and polishing the chamber mouths, refitting the forearm if necessary, replacing the latch lever safety spring for a lighter feel on the thumb lever, disengaging the automatic safety, installing stainless steel firing pins and light weight springs (depending on the shotgun make), manually adjusting the forearm to insure an easy open of the chamber, tuning or replacing hammer springs and finally test firing and checking for proper extraction and release of spent shells.

We don't do action work on all double barrel shotguns. Stoeger, Baikal, Huglu, Charles Daly, CZ, Browning and TNN are the most common shotguns that we work on. If you have something different, PLEASE call to see if it's one that we can work on. Single or double trigger coach-guns can be worked on as well.

PISTOLS

Colt Single Action Armies & Clones

 Action Job $210

*Includes honing and polishing of all internal parts includes barrel and chambers, seer and hammer will be re-cut to a 2-3lb pull, headspace gets checked, the pall and spring will be adjusted to allow for a “free spin” on the cylinder, the stock springs will be replaced with “Lee’s gunslingers” spring kits.

Ruger Vaqueros & Blackhawks

 Action job $210

Includes honing and polishing of all internal parts. Seer and hammer will be re-cut to a 2-3lb pull. Headspace in the cylinder will be checked. The pall and spring will be adjusted to allow for a “free spin” on the cylinder. The stock springs will be replaced with “Lee’s gunslingers” spring kit.